Application of Reliability Simulation in Torpedo Products

WANG Douhui; CHEN Huan; GUO Jun; WU Bin

doi:10.11993/j.issn.2096-3920.2023-0030

Volume 32 Issue 1

Feb 2024

Turn off MathJax

Article Contents

Article Navigation > Journal of Unmanned Undersea Systems > 2024 > 32(1): 166-173

WANG Douhui, CHEN Huan, GUO Jun, WU Bin. Application of Reliability Simulation in Torpedo Products[J]. Journal of Unmanned Undersea Systems, 2024, 32(1): 166-173. doi: 10.11993/j.issn.2096-3920.2023-0030

Citation:

WANG Douhui, CHEN Huan, GUO Jun, WU Bin. Application of Reliability Simulation in Torpedo Products[J]. Journal of Unmanned Undersea Systems, 2024, 32(1): 166-173. doi: 10.11993/j.issn.2096-3920.2023-0030

Citation:

PDF( 15347 KB)

Application of Reliability Simulation in Torpedo Products

doi: 10.11993/j.issn.2096-3920.2023-0030

1.
CEPRI, Guangzhou 615123, China
2.
The 705 Research Institute, China State Shipbuilding Corporation Limited, Xi’an 710077, China

Received Date: 2023-03-24
Accepted Date: 2023-08-17
Rev Recd Date: 2023-05-24

Available Online: 2024-01-29

Abstract

Abstract

The traditional reliability test is time-consuming and requires high cost. Therefore, this article provided the basic content and workflow of reliability simulation and conducted reliability simulation modeling, thermal stress simulation analysis, vibration stress simulation analysis, fault prediction, and reliability evaluation for typical electronic components in a certain torpedo product, so as to obtain weak links in product design, potential fault information, and average first failure time. The analysis results show that the reliability simulation can ensure the elimination of fault sources in the early stage of torpedo product design and thus improve torpedo product robustness and fault prediction ability.
- torpedo,
- reliability,
- electronic components,
- simulation modeling,
- stress analysis

FullText(HTML)

References(9)

References

[1]	胡湘洪, 高军, 李劲. 可靠性试验[M]. 北京: 电子工业出版社, 2015.
[2]	Metzner K J, Wilke U. European THERFAT project—thermal fatigue evaluation of piping system “Tee”-connections[J]. Nuclear Engineering and Design, 2005, 235(2-4): 473-484. doi: 10.1016/j.nucengdes.2004.08.041
[3]	刘贤. 机载电子设备机箱的热场分析与仿真技术研究[D]. 西安: 西安电子科技大学, 2009.
[4]	乔峰. 机载电子设备结构功能模块的抗振设计与优化[D]. 成都: 电子科技大学, 2011.
[5]	Cipière M F, Duff J A. Thermal fatigue experience in French piping: Influence of surface condition and weld local geometry[J]. Welding in the World, 2002, 6(1-2): 23-27.
[6]	Dahlberg M, Nilsson K F, Taylor N, et al. Development of a European procedure for assessment of high cycle thermal fatigue in light water reactors: Final report of the NESC-thermal fatigue project[R]. Netherlands: [s. n.], 2007.
[7]	Blondet E, Faidy C. High cycle thermal fatigue in French PWR[C]//10th International Conference on Nuclear Engineering. Arlington, Virginia, USA: ICONE, 2009.
[8]	Taheri S. Some advances on understanding of high cycle thermal fatigue crazing[J]. Journal of Pressure Vessel Technology, 2007, 129(3): 400-410. doi: 10.1115/1.2748822
[9]	余俊, 王启义, 卜炎, 等. 中国机械设计大典[M]. 南昌: 江西科技技术出版社, 2002.