Citation: | LI Yong-dong, BAI Kun-xue, MA Xiao-lu, YI Yin, NIU Hong-lei. Design and Simulation of Second-order Elliptic Gear in Proportional Controller[J]. Journal of Unmanned Undersea Systems, 2021, 29(4): 459-463. doi: 10.11993/j.issn.2096-3920.2021.04.013 |
[1] |
查志武, 史小峰. 鱼雷热动力技术[M]. 北京: 国防工业出版社, 2006.
|
[2] |
罗凯, 王育才. 一种阀式配比调节器的研制[J]. 机床与液压, 1998(5): 39, 85.
|
[3] |
罗凯, 党建军, 王育才. 三路比例控制器比例精度分析[J]. 机床与液压, 2004(10): 129-130.
Luo Kai , Dang Jian-jun, Wang Yu-cai. Proportion Precision Analysis of Tri-Proportion Controller[J]. Machine Tool & Hydraulics, 2004(10): 129-130.
|
[4] |
王鹰. 三组元比例控制器研究[D]. 西安: 西北工业大学, 2009.
|
[5] |
种衡阳. 凸轮式三元比例控制器结构设计与性能分析[D]. 西安: 西北工业大学, 2010
|
[6] |
郭芳. HAP三组元比例控制器内流场数值模拟与分析[D]. 西安: 西北工业大学, 2012.
|
[7] |
李壮云. 液压元件与系统[M]. 北京: 机械工业出版社, 2011.
|
[8] |
李福生. 非圆齿轮[M]. 北京: 机械工业出版社, 1975.
|
[9] |
张瑞, 吴序堂, 聂钢. 高阶变性椭圆齿轮的研究与设计 [J]. 西安交通大学学报, 2005, 39(7): 726-730.
Zhang Rui, Wu Xu-tang, Nie Gang. Study and Design on High-Order Deformed Elliptic Gears[J]. Journal of Xi’an Jiaotong University, 2005, 39(7): 726-730.
|
[10] |
于文翠, 赵凤芹.基于Pro/E的椭圆齿轮三维参数化造型方法的研究[J]. 机械设计与制造, 2006(3): 54-56.
Yu Wen-cui, Zhao Feng-qin. Studied on the Ellipse Gear Three-dimensional Parameter Modeling with Pro/E[J]. Machinery Desingn & Manufature, 2006(3): 54-56.
|
[11] |
胡赤兵, 姚洪辉. 基于MATLAB及Pro/E的参数化非圆齿轮设计[J]. 机械传动, 2010, 34(7): 33-35.
Hu Chi-bing, Yao Hong-hui. The Parametric Design Research of Nocircle Gear based on MATLAB and Pro/E[J]. Journal of Mechanical Transmission, 2010, 34(7): 33-35.
|
[12] |
刘炀, 袁媛, 韩江. 高阶变性椭圆类非圆齿轮副设计与仿真[J]. 机械传动, 2014, 38(12): 37-38.
Liu Yang, Yuan Yuan, Han Jiang. Design and Simulation of the High Order and Denatured Ellipse of the Non-circular Gear Paris[J]. Journal of Mechanical Transmission, 2014, 38(12): 37-38.
|
[13] |
齿轮手册编委会. 齿轮手册(上册)[M]. 北京: 机械工业出版社, 2006.
|
[14] |
周永清, 朱思洪. 使用CAXA与Pro/E的渐开线椭圆齿轮三维建模与运动仿真[J]. 工程图学学报, 2009, 30(3): 207-211.
Zhou Yong-qing, Zhu Si-hong. Study on 3D Modeling and Kinematics Simulating of Involute Elliptic Gears Based on CAXA and Pro/E[J]. Journal of Engineering Graphics, 2009, 30(3): 207-211.
|
[15] |
胡仁喜. UG NX7.0机械设计完全实例教程[M]. 北京: 化学工业出版社, 2010.
|